CSWIP Welding MCQ Questions
Build CSWIP welding inspection confidence with short MCQs, answer explanations, and related practice questions.
Popular search topics
Searchable question pages
Approved public questions with clean URLs, answer options, and explanation pages.
In GMAW MIG/MAG welding, which mode of metal transfer uses frequencies in cycle time?
In GMAW MIG/MAG welding, which mode of metal transfer uses frequencies in cycle time?
Open 194Post weld heat treatment is used to reduce
Post weld heat treatment is used to reduce
Open 195Weld decay can be minimized by specifying a steel with
Weld decay can be minimized by specifying a steel with
Open 196Weld decay cause which of the following problem
Weld decay cause which of the following problem
Open 197The temperature at which chromium carbide is formed is in the range
The temperature at which chromium carbide is formed is in the range
Open 198What is a typical ARC voltage setting when welding with TIG (GTAW) process in AC?
What is a typical ARC voltage setting when welding with TIG (GTAW) process in AC?
Open 199Why is it essential to clean the excess weld metal on completion of the production weld?
Why is it essential to clean the excess weld metal on completion of the production weld?
Open 200To assess surface of a weld for indirect inspection, the distance from the surface to the eyes should be a maximum of
To assess surface of a weld for indirect inspection, the distance from the surface to the eyes should be a maximum of
Open 201What is the recommended minimum range of illumination required by BS EN 970 for inspection of a welded surface?
What is the recommended minimum range of illumination required by BS EN 970 for inspection of a welded surface?
Open 202Who should select the specific welds for NDT, to cover the 10% contractual percentage required by the specification code
Who should select the specific welds for NDT, to cover the 10% contractual percentage required by the specification code
Open 203Who determines what the correct preparation (root gap, root face, included angle) should be?
Who determines what the correct preparation (root gap, root face, included angle) should be?
Open 204In a transverse weld tensile test, if the break was in the weld material, the sample would be
In a transverse weld tensile test, if the break was in the weld material, the sample would be
Open 205In a welder qualification testing of 45 mm plates, why are side bends used instead of root and face bends
In a welder qualification testing of 45 mm plates, why are side bends used instead of root and face bends
Open 206When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been formed through 180°
When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been for...
Open 207In a cross joint tensile test, the following observations were made; specimen width: 20mm, material thickness: 20mm, max load 180KN, break position: parent plate. What is the UTS?
In a cross joint tensile test, the following observations were made; specimen width: 20mm, material thickness: 20mm, max load 180KN, break positi...
Open 208Charpy impact test showing rough torn surface after the completed test, this would indicate which type of failure
Charpy impact test showing rough torn surface after the completed test, this would indicate which type of failure
Open 209A butt weld has been made by MMA in a 50 thick impact tested steel plate. The welding electrode used was a basic type 5mm diameter, the measured running parameters for one run was
A butt weld has been made by MMA in a 50 thick impact tested steel plate. The welding electrode used was a basic type 5mm diameter, the measured...
Open 210When welding medium carbon steel plates over 100 mm in thickness would the basic electrodes require any pretreatment before use?
When welding medium carbon steel plates over 100 mm in thickness would the basic electrodes require any pretreatment before use?
Open 211Which of the following commonly used radioactive isotopes has the longest half-life?
Which of the following commonly used radioactive isotopes has the longest half-life?
Open 212For MPI using the prods methods, which of the following statements is true
For MPI using the prods methods, which of the following statements is true
Open 213With which of the following NDE processes is it possible to detect both surface and slight sub-surface defects up to 2 mm below the surface
With which of the following NDE processes is it possible to detect both surface and slight sub-surface defects up to 2 mm below the surface
Open 214What would be the most likely SAW flux type for welding medium carbon steel which requires impact testing?
What would be the most likely SAW flux type for welding medium carbon steel which requires impact testing?
Open 215Which of the following defects is usually associated with the MAG (GMAW) welding process when using DIP transfer?
Which of the following defects is usually associated with the MAG (GMAW) welding process when using DIP transfer?
Open 216How is preheat for tack welds during assembly and fit up determined?
How is preheat for tack welds during assembly and fit up determined?
Open