CSWIP Welding MCQ Questions
Build CSWIP welding inspection confidence with short MCQs, answer explanations, and related practice questions.
Popular search topics
Searchable question pages
Approved public questions with clean URLs, answer options, and explanation pages.
Large diameter pipe with a wall thickness of 10 mm is to be used for a cross-country pipeline. Which electrode type could be used to combine high welding speed and deep penetration
Large diameter pipe with a wall thickness of 10 mm is to be used for a cross-country pipeline. Which electrode type could be used to combine high...
Open 338Which NDT method is associated with the use of a yoke?
Which NDT method is associated with the use of a yoke?
Open 339A transverse tensile test piece will give:
A transverse tensile test piece will give:
Open 340Weldments in carbon manganese steels, made by low heat input welding, may show:
Weldments in carbon manganese steels, made by low heat input welding, may show:
Open 341When measuring arc voltage where should the measuring instrument be connected?
When measuring arc voltage where should the measuring instrument be connected?
Open 342Using a stabilized stainless steel will reduce the risk of:
Using a stabilized stainless steel will reduce the risk of:
Open 343Standard oxy-fuel gas cutting equipment can be applied to:
Standard oxy-fuel gas cutting equipment can be applied to:
Open 344Which of the following types of imperfection is generally considered to be the most serious?
Which of the following types of imperfection is generally considered to be the most serious?
Open 345Which polarity is normally used for TIG Welding of aluminum?
Which polarity is normally used for TIG Welding of aluminum?
Open 346Weldments in carbon manganese steels, made using a heat input higher than the maximum specified by:
Weldments in carbon manganese steels, made using a heat input higher than the maximum specified by:
Open 347The output characteristics of a typical MIG/MAG set is:
The output characteristics of a typical MIG/MAG set is:
Open 348Which of the following standards is concerned with welder approval?
Which of the following standards is concerned with welder approval?
Open 349A long centerline crack has been detected in a submerged arc weld bead
A long centerline crack has been detected in a submerged arc weld bead
Open 350A steel designated as 'Z' quality will have:
A steel designated as 'Z' quality will have:
Open 351Which of the following MMA electrode types is generally only suitable for welding in the PA & PB positions?
Which of the following MMA electrode types is generally only suitable for welding in the PA & PB positions?
Open 352Laminations in metal are caused during which of the following?
Laminations in metal are caused during which of the following?
Open 353In MIG/MAG Welding, wire feed speed is proportional to:
In MIG/MAG Welding, wire feed speed is proportional to:
Open 354A typical temperature for normalizing carbon manganese steel is:
A typical temperature for normalizing carbon manganese steel is:
Open 355From examination of the fracture faces, a ductile failure can be identified by:
From examination of the fracture faces, a ductile failure can be identified by:
Open 356A code gives the acceptance standard for excess weld metal “h” as h > 1 mm + 0.1b, max. 5 mm; where “b” is the width of the weld cap. For which of the following situations is the e
A code gives the acceptance standard for excess weld metal “h” as h > 1 mm + 0.1b, max. 5 mm; where “b” is the width of the weld cap. For which o...
Open 357Which welding parameter has the greatest influence on heat input?
Which welding parameter has the greatest influence on heat input?
Open 358A fillet weld has a design throat thickness of 8 mm. What is the minimum leg length that is required?
A fillet weld has a design throat thickness of 8 mm. What is the minimum leg length that is required?
Open 359In a martensite grain structure, which of the following mechanical properties would be increased?
In a martensite grain structure, which of the following mechanical properties would be increased?
Open 360Which of the following alloying elements is used to improve the toughness of steel?
Which of the following alloying elements is used to improve the toughness of steel?
Open